True Triaxial Strength Characteristics of Frozen Silty Sand
DOI: https://doi.org/10.62517/jcte.202606406
Author(s)
Haisheng Hong, Jie Zhu, Jie Wang
Affiliation(s)
School of Civil Engineering, Anhui University of Science and Technology, Huainan, China
Abstract
The strength parameters of artificially frozen ground must consider the intermediate principal stress and temperature. Fengtai, Huainan remolded silty sand was tested under true triaxial tests at temperatures -5, -10 and -15 degrees Celsius. The lowest principal stress was 0.5, 1 or 2 MPa and the coefficient of intermediate principal stress b varied between 0 to 1. Failure stresses were measured as cohesion and friction angle, and failure stress ratio M was used to measure normalized strength response. Cohesion usually rose and then fell with b but the friction angle attained its highest tabulated value at b=0.75 at all three temperatures. Both parameters were raised by cooling at a constant b. Their varying behavior at high b indicates that ice bonding and resistance to friction cannot be captured in one enhancement factor. M had a peak at b=0.75 in all the temperature-confinement series and it grew with confinement, but its dependence on temperature was unlike that of cohesion and friction angle. A quadratic relation was fitted to describe the variation of M𝑀M with b𝑏b, with reported coefficients of determination greater than 0.95. Comparisons with the Drucker–Prager and FKZ criteria showed that the FKZ curves were closer to the experimental friction-angle curves for the selected cases. These results justify selection of temperature- and stress-state-dependent parameters for frozen walls in underground construction.
Keywords
Frozen Silty Sand; True Triaxial Test; Intermediate Principal Stress; Cohesion; Friction Angle; Failure Stress Ratio
References
[1] Yuan P, Hao J, Qi S, et al. Application of the sand-cone method in testing highway subgrade compaction. Soil Engineering and Foundation, 2026, 40(3): 584–587.
[2] Zhao N, Wang S, Wang L, et al. Prediction of the shear strength of frozen silty sand using Boosting, Bagging, Stacking, and Voting ensemble learning models. Journal of Glaciology and Geocryology, 2026, 48(2): 606–615.
[3] Zhang P, Yang C, Du X, et al. Mechanical response during tunnel excavation in artificially frozen sandy–gravelly strata. Chinese Journal of Underground Space and Engineering, 2026, 22(3): 1013–1022, 1033. DOI: 10.20174/j.JUSE.2026.03.27.
[4] Chen J, You Z, Zhou Y. Development of freezing temperature fields under different seepage directions. Journal of Railway Science and Engineering, 2026, 23(2): 821–832. DOI: 10.19713/j.cnki.43-1423/u.T20251109.
[5] Li J. Effects of freezing–thawing and wetting–drying cycles on the mechanical properties and microstructure of biopolymer-treated dispersive soil. Dissertation. Changchun: Jilin University, 2025. DOI: 10.27162/d.cnki.gjlin.2025.005097.
[6] Wang K. Hydrothermal characteristics and regulation methods for high-speed railway embankments in high-latitude discontinuous permafrost regions. Dissertation. Harbin: Harbin Institute of Technology, 2024. DOI: 10.27061/d.cnki.ghgdu.2024.003237.
[7] Wang Z, Yao Z, Zhang H, et al. Creep characteristics of water-bearing weakly cemented Jurassic sandstone in western mining areas. Journal of Jiamusi University (Natural Science Edition), 2025, 43(9): 67–70. DOI: 10.20232/j.cnki.jmsdxxb.2025.09.012.
[8] Wang S, Zhang X, Zhou B, et al. Freezing–thawing and strength characteristics of artificially frozen cement-treated soft clay. Journal of East China University of Technology (Natural Science), 2024, 47(4): 370–380.
[9] Yao Z, Liu J, Wang X. Prediction of the stress–strain relationship of artificially frozen soil using a KOA-LSTM model. Journal of Jiamusi University (Natural Science Edition), 2026, 44(4): 113–116, 82. DOI: 10.20232/j.cnki.jmsdxxb.2026.04.016.
[10] Jariyatatsakorn K, Kongkitkul W, In P Y. Temperature- and rate-dependent stress–strain–time behavior of sands and its simulation using a modified nonlinear three-component model. Arabian Journal for Science and Engineering, 2026, advance online publication: 1–24. DOI: 10.1007/s13369-026-11378-9.
[11] Hashim M Y, Qiao Fei Yang, Peng Da Li. Load path dependence for passively and actively confined high-strength concrete. Construction and Building Materials, 2024, 440: 137353. DOI: 10.1016/j.conbuildmat.2024.137353.
[12] Quan L, Tian B, Li S, et al. Driving factors and climate resilience of highway embankment deformation in permafrost regions of the Qinghai–Tibet Plateau. Journal of Traffic and Transportation Engineering, 2025, 25(5): 38–52. DOI: 10.19818/j.cnki.1671-1637.2025.05.003.
[13] Liang J, Hu X, He L, et al. Temperature and strain-rate effects on the uniaxial mechanical behavior and constitutive relationship of frozen soil. Journal of Disaster Prevention and Mitigation Engineering, advance online publication: 1–12, accessed August 10, 2026. DOI: 10.13409/j.cnki.jdpme.20251103001.
[14] Fan M, Liu C, Qiao Z, et al. Triaxial shear characteristics of sand–red clay mixtures and validation of the Duncan–Chang model. Journal of Jiamusi University (Natural Science Edition), 2026, 44(7): 87–90, 156. DOI: 10.20232/j.cnki.jmsdxxb.2026.07.009.
[15] Cao Y, Rong C, Wang Y, et al. Mechanical response and constitutive modeling of frozen calcareous clay under complex stress paths. Rock and Soil Mechanics, 2025, 46(7): 2071–2084. DOI: 10.16285/j.rsm.2024.1265.
[16] Shen C, Wang W, Zhong J, et al. Experimental study of the static and dynamic properties of silty sand at the Jiuweigang sluice-station project site. Jiangsu Water Resources, 2024, (7): 47–52. DOI: 10.16310/j.cnki.jssl.2024.07.016.